sanguinololu 1.3b IC1 hot (1 reply)
Yesterday I got my reprap.me sanguinololu 1.3b - soldered the connectors, powered it up using a 1A 12V power supply(no steppers or stepper controllers attached), uploaded the firmware and made sure...
View Articlesanguinololu 1.3b and the 12864 LCD (1 reply)
I bought the Full graphic display to go with my new Sanguinololu. Unfortunately it came with the RAMPS smart adapter only. I've been staring at both, the 1.3b and Graphics displays schematics on the...
View Articleneed help with solder tip :( (no replies)
hi everyone, just became a member here a few minutes ago, been lurking here for quite a while before that though. so i reeeeeeally need some help right now: i almost got my purse i3 finished, and...
View ArticleSanguinololu V1.3B Mods (no replies)
Hello... I'm in building proces for my 1st printer. For electronics I just ordered Sanguinololu V1.3B. But there are some bugs/mods proposed. Sadly I can't find board layout (or gerbers) for that...
View ArticleReprap Discount Smart Controller Not Working (3 replies)
Hi All, Have a mendelmax 1.5 using sanguino 1.3a & latest Marlin firmware. Frustrated with the smart controller I bought from here. According to guys like this, it should be just as easy as...
View Articleu8glib pins error (no replies)
Hi, I have full graphic lcd and wanted to use with my sangui 1.3a but whenever I tried to upload the firmware the ide gave me u8glib error on the pins, something like not declared or something. A help...
View Articlesanguinololu 1.3 ATX power switching using the m80 gcode commands (no replies)
Hi all I have my home built printer in the garage and although I dont mind leaving it running during a long print, I would very much like to be able to use the M80/81 code at the start and end of my...
View ArticleMelzi upload problem (4 replies)
Hello, folks! sad to say i am a complete noob at arduino. so here is the deal. i am trying to upload marlin firmware to my melzi board with 1284p atmega chip. Compilling goes without any error, but...
View Articlecompile troubles (3 replies)
hello! i try to compile marlin with full graphic display support for my melzi, but i got error in U8glib (which is installed latest version) i run windows 8.1. x64 and arduino ide 1.5.8. beta. on non...
View ArticleSanguino what is a good replacement (no replies)
Hi all, Seems that the Sanquinololu board has a few minor issue \ bugs, they all have pretty easy work a rounds so the board is still very useful. My question is what would be the next level up from...
View Articleproblem with sanguinololu (1 reply)
It was working and now my extruder stopped working. I connected my extruder stepper motor to z axis and it turns. This means the extruder stepper motor is working I then swap out the z axis and...
View ArticleHesine Melzi 2.0 arduino source files (1 reply)
Wondering if anyone has the arduino build files for this or this controller. (Melzi v2.0) I'd like to be able to try some different print heads in the future but without those it will be a little hard...
View ArticleMelzi V2.0 board Repetire question (no replies)
I've been working with my new printer, and by the way I'm new to all this and still learning. When I power up the printer I see on the display screen Omni 1.04 Not sure if this is the firmware or what...
View ArticleCan't connect to Melzi, but uploading firmware works fine! (2 replies)
Hello RepRapers, I can't connect to my Melzi board via USB any more. It has worked flawlessly before with Pronterface, Repetier Host and Simplify3D. However, I can upload new firmware to the Melzi...
View ArticleMAXTEMP Error (2 replies)
Hello, My Prusa i3 is allways showing Max temp error on the extruder. The thermistor is fine but even without a thermistor it shows max temp. The bed temp is fine. Furthermore i cant control the axis...
View ArticleClik here to view.
Problems with Sensor (2 replies)
Hi everyone I'm having some problems getting my capacitive sensor working with my Melzi 2.0 and I was hoping to get some feedback from you. I bought a LJC18A3-B-Z/BY PNP NO Capacitive sensor from Ebay...
View ArticleProblem with my sanguinololu.. (4 replies)
Hello, so i decided to build back my 3d printer and i am facing a problem with my sanguino (rev 1.3a if i'm not mistaken) The j-head doesn't receive any power. The board looks in good state, nothing...
View ArticleShorted out pololu? (1 reply)
So I was trying to dial in my pololus this morning, and I managed to touch the screwdriver to something I shouldn't have. There were sparks. Now my Y axis motor will only vibrate loudly when it should...
View ArticleProblems after swapping drivers (2 replies)
Last week I managed to fry one of my pololus (y axis) by shorting it out with a screwdriver. I ordered a generic stepstick driver to replace it. After installing it today and adjusting the current I...
View ArticleMelzi V2 for laser engraving (no replies)
Hi, I whant to use my printer also for laser engraving . Is it possible with Melzi V2? What should I do? Hope I'm not the first one. Thanks
View Article