euroway RipRep prusa i3 3d Printer????? (8 replies)
I would like to know if anyone out there can really help me? this is the second 3d printer I have gotten and can't get eather one of the DARN things to work. this newest one is the Euroway (hahaha)...
View Articleheatbed issue (no replies)
Hi, I'm going crazy with my heat bed issue hoping someone here could help. I have 1.3a rev. and recently added a heat bed to it. With updated firmware (added heat bed and thermistor settings in...
View ArticleProntoface not connecting (3 replies)
I'm using Windows7, a Sanguinololu 1.3a and prontoface on a machine I have built myself. I have had this machine printing out successfully in the past but now it refuses to work.p When I attempt to...
View ArticleMelzi v2: Motor current on the z axis that is not 0,6V (no replies)
My printer is Huxley, in Melzi V2, should the voltage should be 0,6V, then I measure if the voltage at the motor potentiometer on the z 0,1V, and the potentiometer was already I swivel maximum. What...
View ArticleHesine Melzi 2.0, marlin firmware upload issue (8 replies)
Hi everyone, I got my first printer recently and I'm trying to upload Marlin to it to enable autolevelling.. I can control the printer through USB (pronterface) but I'm having trouble flashing the...
View ArticlePuzzle: Analog inputs work with E3D PT100 but cannot read normal thermistor...
I have been pulling my hair out with this problem, and I am looking for a good explanation of what the hell is going on. I just upgraded my electronics from a Sanguinololu to a RAMB0, and in the...
View ArticleRepRapPro Huxley (Sanguinololu) + LCD SainSmart Problem (1 reply)
Hi, I wanted to connect the SainSmart 2004 Smart LCD Controller to my RepRapPro Huxley. My problem is, that one pin is used. It´s the bed heater control. (This pin is labelled D10: it has a 5V signal...
View ArticleDoes this also Melzi v2.0 for Huxley? (no replies)
Because RepRap Pro already closed their shops, I want to buy Melzi v 2.0 here:[www.amazon.com]. Can I use it to Huxley?
View ArticleLCD resets / blanks out when I touch the Ground (no replies)
I spent so much time trying to figure this out but every attempt failed. When I switch on my printer: • The menu on the LCD shows nicely • Bed and Nozzle heat up OK • XYZE move ok • It can print with...
View ArticleNeed help with sanguino (2 replies)
Hi everyone I've got a pusa i3 with sanguino board. Suddenly while i was printing the printer stopped and showed on lcd screen error maxtemp at extruder's thermistor. I changed thermistor, i tried to...
View ArticleWorking, then not, now 7805 is hot ;( (no replies)
Hi guys I bought a kit from alibaba (geetech aluminum i3 prusa) and it was working fine (could do manual control over repetier host, homing, bed/extruder heating). The only thing that was missing was...
View ArticleVerifying bootloader and/or firmware on Sanguinololou with ATMega1284P (no...
All, I'm a newb to this, and have been messing with a buddy's GeeeTech 3D printer. It has a Sanguinololou board on it, and I wanted to load the Marlin FW. However, having already bricked one 1284, I...
View ArticleHelp with Firmware upload (1 reply)
Hi! I have a problem with my Sanguinololu 1.3a I recently wanted to upload to it Marlin firmware, because I had to install new ATMEGA1284P-PU microcontroller, but in Arduino 0023 I keep getting...
View ArticleMelzi lost USB connection (no replies)
Hi all. During printing the other day I had my Prusa clone jamb to the extent that it tripped the house mains supply. On powering up again every thing works except there is no communication via USB....
View Article1284P Fuse settings confirmation? (3 replies)
Hey all, trying to get my repstrap up and running (Sanguinololu w/ a 1284p). I'm seeing different fuse settings depending on where I look. Currently I'm set to (l,h,e) D6,DA,FD. But I've also seen...
View ArticleNeed AVRDUDE guru/bootloader help (1 reply)
So here is the situation. I am using an Arduino UNO (Actually and OSEPP Uno R3 Plus) as an ISP programmer. The target board is a Melzi V3 Ebay upgrade to an ATmega1284P chip. Running the...
View Article`.text' will not fit in region `text' during compile of firmware (1 reply)
I am trying to write the bootloader and firmware to the Sanguino controller board on my reprap printer. I got an SD card with the package that supposedly had all the software for the system. After...
View ArticleSanguinololu with at1284p (1 reply)
Hello, I'm struggling with this one for a couple of days, and decided to come here and ask for some tips... I'm trying to upload a Marlin firmware to a sanguinololu but without success... I'm working...
View ArticleSanguinololu 1.3a Huxley connection problem (4 replies)
Hi all, I posted this in the Huxley section but figured it should maybe be in the Sanguinololu section. I apologize if I shouldn't do that. I recently was given a Huxley 3d printer - the one from the...
View ArticleSanguinololu Rev 1.3a - how to load firmware (8 replies)
Hi all, I just got a new Sanguinololu Rev 1.3a board for my old Huxley printer. (the old one was broken) From what I understand I need to load the firmware and possibly a bootloader? I don't know...
View Article