Help with sanguinololu electronics (1 reply)
i have a sanguinololu 1.3a with ATMEGA 1284P. bootloader and firmware already installed but i need help with drivers im getting a This device can not start (code 10). i have installed arduino files...
View ArticleSanguinololu 1.3a 1284p - no power at heatbed. (5 replies)
Hi. Im new in 3d printing and im trying to finish my mendel Prusa with Sanguinololu 1.3a and i have a problem. There is no power at heatbed. I measured power on hot-end - there is normal 12V. When i...
View ArticleVerification failure after upload? (9 replies)
Hey everyone, I built up a Sanguinololu completely from scratch. It seems that almost everything is working. I can compile a small test program and upload it with avrdude. Everything works correctly...
View ArticlePanelou & Sanguino setup ? (no replies)
I'm trying to connect a new Panelou LCD to my Sanguino board 1284p (with onboard MARLIN ) So how do I actually get the Sanguino to recognize Panelou LCD board ?? I read that I need to use Arduino to...
View ArticleClik here to view.
Help Fixing a Sanguinololu After Mistake (3 replies)
Looks like when soldering in some header pins I bridged a couple other pins! The rest of the board seems to work, so I just need someone familiar with Sanguinololu 1.3a to tell me what to jump to the...
View ArticleEndstop don't work, when more than one endstop are connected (1 reply)
Hi everyone, The electronic I use is the Sanguinololu, I have here one problem with the endstop. The endstops will not work, when several endstops are connected on the Sanguinololu. I tried to connect...
View ArticleWhy are end stops NO instead of NC? (no replies)
I am using a sanguinololu 1.3a solution for my 3D printer. When I purchased my endstops they sent me NC instead of NO. Will it cause a problem if NC end stops are used? Why are end stops NO instead of...
View ArticleSanguinololu homing/end stop problems (2 replies)
Hello, I am in the process of building an Ultimaker like Reprap using a Sanguinololu as controller with Repetier software and firmware. It's almost finished, except for the belts and pulleys for the...
View Articlehelp with twitching steppers (2 replies)
i am building a prusa mendel i3 with sanguino 1.3a and everything was working perfectly when all the motors decided to stop working. whenever i use the manual controls with repetier host all the...
View ArticleSanguinololu 1.3a X axis stepper motor shaky movement (1 reply)
Hello I am having problems with the movement of the x axis using a Sanguinololu. The printer was initially working fine but after pausing a print the motion of the x axis has become erratic. The axis...
View ArticleUsing extra IO ports in Marlin? (4 replies)
Hi, I am using a melzi, a sanguinololu-based board for my next reprap. I would like to use some pins on the expansion header for digital IO. In particular, I need two inputs, an emergency-off switch,...
View ArticleWhat Software do I need? (2 replies)
I'm building my first 3d printer. I'm thinking about going with the sanuniololu board since its relativly cheap. What software will i need to run it? (I've never used any of this Arduino stuff...
View ArticleUsing L297/L298 with Sanguino (6 replies)
Hi, I have burnt like 8 Polulu/Stepsticks. Those are costly and have long waiting time. So I was trying to run it with L297/L298. The only problem is Polulu/Stepstick the DIR signal is on high, while...
View ArticleEndstops pullup resistors always low (2 replies)
Hello everyone, Am having some problems with my sanguino. The endstops don't seem to work they stay in the low configuration. First I thought I might have blown up the ATmega so I ordered another one....
View Articlei've got endstops and X axis issues (no replies)
hi there, i've got problems to start up my Mendel. it's built with Sanguinolou v1.3a w/ATmega644P. i've just succeeded to upload the Marlin firmware with Arduino 0018 runing on windows 7/64b. i'm...
View ArticleHotend Problem (1 reply)
Hello guys I built a Mendel using Sanguino electronics. I ran my first test print, and everything appear to work fine with one exception. My J-head hotend heats to the desire temperture of 185...
View ArticleProblem with Power Supply (4 replies)
Hey, I have a Sanguinololu Board with Screw Terminals. I bougth a PC Power Supply and connect the 12V output and the Ground to my Sanguinololu Board. If i plug it in the red LED on my Sanguinololu is...
View ArticleHeatsink shorted pololu, sanguino can no longer connect (3 replies)
So, as i was placing my pololus back onto my sanguino, and I didn't notice until too late that one of the pololu heatsinks was slightly off kilter. As soon as i turned on 12v I heard that signature...
View ArticleConnecting Problems Prusa i3 with Sanguinololu (no replies)
Hi All, I am new on the 3D Printer scene and have the following problems, (until now, that is...:-) )+ building a Prusa i3 with Sanguinololu with Cura I can not find the Sanguinololu board listed in...
View Articlegen3 Temperature.h:331: error: 'bedtemptable' was not declared in this scope...
Can anyone tell me how to fix this or which part to look at. TY .Compiling error : gen3 Temperature.h:331: error: 'bedtemptable' was not declared in this scope.
View Article